If you have been reading about mass spectrometry and want a single page that covers the useful parts, this is it: definitions, context, how it is studied, and the questions that come up repeatedly.
Last reviewed on 2025-09-19. Where a claim depends on a specific study, the study is described rather than over-claimed.
Reported purity values can differ between laboratories even for the same sample. Variations arise from column chemistry, mobile-phase composition, gradient slope, detection wavelength, injection load, and integration rules. Area percent also assumes that all species have similar response factors, which is not always true. Method validation examines specificity, linearity, accuracy, precision, limit of detection, and limit of quantitation. When comparing certificates, the method description and representative chromatogram are as important as the headline percentage.
Purity and potency are related but distinct concepts in peptide testing. Purity describes the proportion of the main peptide relative to other detected substances, while potency refers to the biological or functional activity of a defined amount. A highly pure peptide can still have low potency if it is misfolded, aggregated, or chemically modified at a critical residue. Conversely, a less pure preparation may retain high activity if the impurities are inactive. Clear reporting separates these attributes and states the assay used for each.
Peptide purity specifications describe which tests define an acceptable lot and how results are reported. A certificate of analysis commonly lists a reverse-phase HPLC purity value, a mass spectrometry identity result, water content, counterion content, and residual solvent data. The specification may set a minimum area percent, such as 95% or 98%, depending on the intended use and grade. No universal threshold applies to all peptides, because sequence length, hydrophobicity, and manufacturing route influence achievable purity.
Handling practices reduce the risk of contamination and degradation. Hygroscopic peptides should be equilibrated to room temperature before opening to prevent condensation on the powder. Weighing and reconstitution in a controlled environment limit exposure to moisture and airborne particles. Aliquotting reconstituted solutions avoids repeated freeze-thaw cycles that can cause aggregation or precipitation. When a purity specification is not met, investigation may consider synthesis byproducts, purification losses, storage conditions, and analytical variability rather than a single cause.
Peptide purity can change during storage, handling, and reconstitution, and lyophilized peptides are generally more stable than solutions because water promotes hydrolysis and aggregation. Residual moisture, oxygen, and trace metals can accelerate degradation even in solid form. Temperature fluctuations during shipping may cause condensation and local moisture uptake. Quality control therefore includes appearance, water content, and analytical testing before and after storage challenges. Peptides containing cysteine, methionine, or tryptophan are especially susceptible to oxidation, while asparagine and glutamine residues can deamidate under neutral or alkaline conditions.
Analytical quality control compares a stored sample against a baseline profile. Reverse-phase chromatography remains common, but stability studies may also use mass spectrometry to detect oxidation, deamidation, or truncation products. Accelerated aging at elevated temperature can reveal degradation pathways, although extrapolation to room temperature is uncertain. Forced degradation studies expose peptides to heat, light, acid, base, and oxidants to identify likely breakdown products. Documentation should record lot number, storage history, and the exact method used for each measurement.
| Property | Value | Notes |
|---|---|---|
| Typical purity specification | 95% or 98% area by RP-HPLC | Grade and application dependent |
| Common identity test | Electrospray ionization mass spectrometry | Confirms molecular mass |
| Typical water content method | Karl Fischer titration | Reports residual moisture |
| Common counterion test | Ion chromatography | Detects trifluoroacetate or acetate |
| Typical validation elements | Specificity, linearity, precision, accuracy | Follows method-validation guidance |
Impurity profiles can include deletion peptides, oxidized forms, truncated sequences, and residual solvents. Some impurities arise during synthesis, cleavage, or purification, while others form during storage. Purity testing often focuses on peptide-related impurities, whereas residual solvents and counterions require separate assays. The significance of a given impurity depends on its amount and properties, which may not be established for a research peptide. Reporting an impurity profile is more informative than reporting a single purity number.
Peptide purity specifications describe the minimum acceptable result from a defined test. A certificate of analysis may list HPLC purity, mass spectrometry identity, appearance, and counterion content. Specifications are method-dependent, so a value obtained with one gradient or wavelength may differ from another. For research use, common thresholds include 95% and 98% by RP-HPLC, but the appropriate limit depends on the application. The specification should always name the analytical method and acceptance criterion.
Chromatographic separation resolves truncated, oxidized, deamidated, and epimerized peptide variants when their retention times differ from the target. Mass spectrometry confirms molecular mass and can reveal modifications that UV detection misses. Liquid chromatography coupled to mass spectrometry combines separation with identity information, which helps distinguish a pure target from a co-eluting impurity. UV-based area percent can overestimate purity if an impurity lacks a chromophore or if the target and impurity have similar response factors. Researchers often report both chromatographic purity and mass confirmation to give a fuller picture.
Additional techniques address components that reversed-phase chromatography may not resolve. Ion-exchange chromatography separates by charge, size-exclusion chromatography detects aggregates, and capillary electrophoresis offers high separation efficiency. Water content is measured by Karl Fischer titration, residual solvents by gas chromatography, and elemental impurities by inductively coupled plasma mass spectrometry. Amino acid analysis or nitrogen determination can estimate peptide content on a mass basis. Purity is frequently reported as area percent, yet standardized comparison across laboratories remains an open question because methods and reporting practices differ.
Peptide purity testing measures how much of a sample consists of the intended peptide sequence compared with related substances, water, counterions, and residual solvents. No single analytical method captures all of these components at once. Reversed-phase high-performance liquid chromatography with ultraviolet detection is widely used because it separates peptides by hydrophobicity. The reported purity value therefore depends on the chosen method, column, mobile phase, and detection wavelength. Established practice treats purity as method-dependent rather than an absolute property of the material.
Other methods address specific purity concerns. Amino acid analysis gives compositional data after hydrolysis, while capillary electrophoresis separates by charge-to-mass ratio. Karl Fischer titration measures residual water, and gas chromatography can detect residual solvents. Nuclear magnetic resonance can identify organic impurities but is less sensitive for trace levels. No single test covers all possible impurities, so purity testing usually combines orthogonal methods and reports the conditions used. The choice of methods is guided by the impurity classes of interest.
Reverse-phase high-performance liquid chromatography (RP-HPLC) is widely used to estimate peptide purity. It separates components by hydrophobicity on a column with a water-organic mobile phase. Ultraviolet absorbance at 214 nm or 220 nm detects peptide bonds. The main peak area as a percentage of total peak area gives a purity figure. This figure depends on column, gradient, wavelength, and how peaks are integrated, so it is method-specific rather than absolute.
Carnitine is an essential cofactor for mitochondrial transport of long‑chain fatty acids (a major lipid class) into the matrix for β‑oxidation. gamma-aminobutyric acid is a neurotransmitter. 5-HTP (5-hydroxytryptophan) is used for experimental treatment of depression. L-DOPA (L-dihydroxyphenylalanine) for Parkinson's treatment, Eflornithine inhibits ornithine decarboxylase and used in the treatment of sleeping sickness. Canavanine, an analogue of arginine found in many legumes is an antifeedant, protecting the plant from predators. Mimosine found in some legumes, is another possible antifeedant. This compound is an analogue of tyrosine and can poison animals that graze on these plants. However, not all of the functions of other abundant nonstandard amino acids are known.
Beta-peptides (β-peptides) are peptides derived from β-amino acids, in which the amino group is attached to the β-carbon (i.e. the carbon two atoms away from the carboxylate group). The parent β-amino acid is β-alanine (H2NCH2CH2CO2H), a common natural substance, but most examples feature substituents in place of one or more C-H bonds. β-peptides usually do not occur in nature. β-Peptide-based antibiotics are being explored as ways of evading antibiotic resistance. Early studies in this field were published in 1996 by the group of Dieter Seebach and that of Samuel Gellman.
In plants, nitrogen is first assimilated into organic compounds in the form of glutamate, formed from alpha-ketoglutarate and ammonia in the mitochondrion. For other amino acids, plants use transaminases to move the amino group from glutamate to another alpha-keto acid. For example, aspartate aminotransferase converts glutamate and oxaloacetate to alpha-ketoglutarate and aspartate. Other organisms use transaminases for amino acid synthesis, too. Nonstandard amino acids are usually formed through modifications to standard amino acids. For example, homocysteine is formed through the transsulfuration pathway or by the demethylation of methionine via the intermediate metabolite S-adenosylmethionine, while hydroxyproline is made by a post translational modification of proline. Microorganisms and plants synthesize many uncommon amino acids. For example, some microbes make 2-aminoisobutyric acid and lanthionine, which is a sulfide-bridged derivative of alanine. Both of these amino acids are found in peptidic lantibiotics such as alamethicin. However, in plants, 1-aminocyclopropane-1-carboxylic acid is a small disubstituted cyclic amino acid that is an intermediate in the production of the plant hormone ethylene.
Amitriptyline was developed by the American pharmaceutical company Merck in the late 1950s. In 1958, Merck approached several clinical investigators proposing to conduct clinical trials of amitriptyline for schizophrenia. One of these researchers, Frank Ayd, instead, suggested using amitriptyline for depression. Ayd treated 130 patients and, in 1960, reported that amitriptyline had antidepressant properties similar to another, and the only known at the time, tricyclic antidepressant imipramine. Following this, the US Food and Drug Administration approved amitriptyline for depression in 1961. In Europe, due to a quirk of the patent law at the time allowing patents only on the chemical synthesis but not on the drug itself, Roche and Lundbeck were able to independently develop and market amitriptyline in the early 1960s. According to research by a historian of psychopharmacology David Healy, amitriptyline became a much bigger selling drug than its precursor imipramine because of two factors. First, amitriptyline has a much stronger anxiolytic effect. Second, Merck conducted a marketing campaign raising clinicians' awareness of depression as a clinical entity. Amitriptyline is no longer sold under the brand name Elavil.
The structure of the AG glycans consists of a backbone of β-1,3 linked galactose (Gal), with sidechains of β-1,6 linked Gal and have terminal residues of arabinose (Ara), rhamnose (Rha), Gal, fucose (Fuc), and glucuronic acid (GlcA). These AG glycan moieties are assembled by glycosyltransferases (GTs). O-glycosylation of AGPs is initiated by the action of Hyp-O-galactosyltransferases (Hyp-O-GalTs) that add the first Gal onto the protein. The complex glycan structures are then elaborated by a suite of glycosyltransferases, the majority of which are bio-chemically uncharacterized. The GT31 family is one of the families involved in AGP glycan backbone biosynthesis. Numerous members of the GT31 family have been identified with Hyp-O-GALT activity and the core β-(1,3)-galactan backbone is also likely to be synthesized by the GT31 family. Members of the GT14 family are implicated in adding β-(1,6)- and β-(1,3)-galactans to AGPs. In Arabidopsis, terminal sugars such as fucose are proposed to be added by AtFUT4 (a fucosyl transferase) and AtFUT6 in the GT37 family and the terminal GlcA incorporation can be catalysed by the GT14 family. A number of GTs remain to be identified, for example those responsible for terminal Rha.
Sources: en.wikipedia.org
ADAMTS7 was identified as a protease that binds and cleaves COMP in a yeast two-hybrid screen using the epidermal growth factor (EGF) domain of COMP as the bait. However, this initial finding has been contested; a 2025 study demonstrated that purified ADAMTS7 does not exhibit proteolytic cleavage activity toward purified COMP. Furthermore, three independent unbiased N-terminal amine isotopic labeling of substrates (N-TAILS) proteomic studies identified a number of candidate substrates for ADAMTS7 but did not identify COMP as a potential substrate. Consequently, there is as yet no scientific consensus on the physiological function of ADAMTS7. Tissue inhibitor of metalloproteinases 4 (TIMP-4) appears to be the physiological inhibitor of ADAMTS7.
“Chemoinformatics and Molecular Simulation”; “Chemistry of Supramolecular Nano- and Biosystems”; “Methods of Analytical Chemistry”; “Physical-Chemical Methods in Chemistry”; “Petrochemistry and Catalysis”. Total number of students taking Bachelor, Specialist and master's degree programs is 472 (as of January, 2016).Departments of the Institute of Chemistry educate postgraduates in the following majors: 02.00.01 – Inorganic Chemistry; 02.00.02 – Analytical Chemistry; 02.00.03 – Organic Chemistry; 02.00.04 – Physical Chemistry; 02.00.08 – Chemistry of Organoelement Compounds. There are two dissertation councils functioning in the Institute of Chemistry for thesis defence in chemical sciences: Д 212.081.03 under the Federal State Autonomous Institution of Higher Education “Kazan (Volga Region) Federal University”; majors allowed for defence: 02.00.01 – Inorganic Chemistry; 02.00.08 – Chemistry of Organoelement Compounds; Chairman of the Council is Professor Vladimir I. Galkin, Doctor of Chemistry;
ASQ offers 18 professional certifications relating to various aspects of the quality profession. Professional certification exams are translated into five languages included English, Korean, Mandarin, Portuguese, and Spanish. Exams are given nationally and, to a limited degree, worldwide several times annually. The body of knowledge for each certification is maintained through peer review every few years on a rotating schedule. In 1968, the first ASQ certification was offered. In 2016, ASQ's certification exam delivery method changed from paper to computer-based testing at Prometric nationwide testing facilities. ASQ publishes a range of magazines and journals: Quality Progress Journal for Quality and Participation Journal of Quality Technology Quality Engineering Quality Management Journal Lean & Six Sigma Review Software Quality Professional Technometrics Journal for Quality Perspectives in Knowledge Acquisition Quality Management Forum Primers on Human Development and Leadership ASQ hosts a number of quality events and annual conferences worldwide:
For decades, the public viewed the house as the "Birthplace of Insulin," and many individuals expressed their desire to have it turned into a shrine or monument to honour the Canadian hero. It was first internationally referred to with the title "Birthplace of Insulin," in 1923, by the Detroit Free Press. After 47 years, the house received official recognition in 1970, in the form of a plaque for the house, awarded by the London Public Library Board. In 1981, the London & District Branch of the Canadian Diabetes Association purchased the house, and began to use it as an office; they hoped to eventually restore the house, and turn it into a museum. Through various grants and fundraising efforts, by 1984, the museum was operational.
The carbon atom next to the carboxyl group is called the α–carbon. In proteinogenic amino acids, it bears the amine and the R group or side chain specific to each amino acid, as well as a hydrogen atom. With the exception of glycine, for which the side chain is also a hydrogen atom, the α–carbon is stereogenic. All chiral proteinogenic amino acids have the L configuration, and can therefore be referred to as L-amino acids. They are "left-handed" enantiomers, which refers to the stereoisomers of the alpha carbon. A few D-amino acids ("right-handed") have been found in nature, e.g., in bacterial envelopes, as a neuromodulator (D-serine), and in some antibiotics. Rarely, D-amino acid residues are found in proteins, and are converted from the L-amino acid as a post-translational modification.
Sources: en.wikipedia.org
Purity percentages vary because each laboratory uses its own column, mobile phase, gradient, detection wavelength, and integration settings. A 95% value from one method may not equal 95% from another method. Comparative assessment requires the same validated procedure or an orthogonal cross-check.
A useful certificate of analysis states the peptide sequence, lot number, test methods, acceptance criteria, and measured results. It typically reports HPLC purity, mass spectrometry identity, water content, counterion content, and residual solvents when relevant. The document should also include a chromatogram and the date of testing.
Higher HPLC purity reduces the relative amount of ultraviolet-detectable impurities, but it does not guarantee correct sequence, stereochemistry, or biological activity. Some impurities may be invisible to the chosen method, and aggregates or counterions may still be present. Fitness for purpose depends on the intended application and the full set of tests.
Most lyophilized peptides are stored desiccated at -20 °C or lower, protected from light. Some sequences require -80 °C for long-term stability. Storage recommendations depend on sequence, moisture content, and expected duration.