The short version of stationary phase fits in a sentence. The long version — which is the one that helps — is below.
Reviewed 2026-08-01. Anything still debated is marked as such rather than presented as settled.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Typical checks include retention time, peak area precision, resolution between critical pairs, tailing factor, and theoretical plate count. Acceptance criteria are set in the method or pharmacopeial monograph. If a suitability check fails, the run may be rejected and the instrument or sample preparation may need investigation. This practice helps prevent release of data from a system that has drifted out of control.
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
| Property | Value | Notes |
|---|---|---|
| Validation parameter | Accuracy | Closeness to a reference value. |
| Validation parameter | Precision | Repeatability or intermediate precision. |
| Validation parameter | Linearity | Proportional response across a range. |
| System suitability check | Resolution | Separation between adjacent peaks. |
| Quality control tool | Control chart | Tracks results over time for trends. |
Detection commonly uses ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. Ultraviolet detection depends on molecular chromophores that absorb light at specific wavelengths. Mass spectrometry provides mass information and sensitive quantification, often after electrospray ionization. Before sample batches, performance checks examine resolution, elution time repeatability, peak symmetry, and plate count. Matrix effects and co-elution remain recognized uncertainties; formal validation studies and orthogonal detection help address them. Detector choice depends on analyte properties and required sensitivity.
High-performance liquid chromatography, or HPLC, separates dissolved compounds by passing a liquid mobile phase through a packed column. Components distribute differently between the stationary phase and the moving liquid, so they travel at different speeds and exit at different times. A detector records these eluting bands as peaks, and peak area or height relates to amount. The technique supports testing in pharmaceuticals, foods, environmental samples, and industrial chemicals. Quantification usually depends on calibration with known standards.
Regulatory and pharmacopeial texts shape how HPLC testing is performed and documented. The International Council for Harmonisation provides validation guidance, while pharmacopeias publish general chromatography chapters and monographs for specific materials. Accreditation standards such as ISO/IEC 17025 address laboratory competence and traceability. Inspectors may review instrument qualification, analyst training, reference material control, and electronic records. Open questions include how best to validate methods for new complex products and how to handle automated data processing. Laboratories generally resolve these issues through risk assessment, method lifecycle management, and documented scientific justification.
In quality control laboratories, HPLC testing supports batch release, raw material checks, stability studies, and impurity profiling. A validated method defines sample preparation, instrument settings, calibration, and acceptance criteria. Analysts compare results with specifications and investigate out-of-specification outcomes before a batch is approved. Documentation includes chromatograms, integration records, audit trails, and reagent details. Because results influence product decisions, laboratories follow formal quality systems and data integrity rules. The exact tests and limits depend on the material, its intended use, and the applicable regulatory framework.
Method validation examines whether an HPLC procedure is suitable for its intended purpose. Common parameters include accuracy, precision, specificity, linearity, range, detection limit, quantification limit, and robustness. Accuracy describes closeness to a true or accepted value, while precision describes agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from related substances. Robustness tests small deliberate changes in flow, temperature, or solvent composition. Validation is not a one-time event; methods may need partial revalidation after changes to instruments, columns, sample handling, or specification limits. Regulatory guidance provides frameworks, but some details remain method-specific.
In the presence of air and various cofactors and enzymes, fatty acids are converted to acetyl-CoA. The pathway is called beta-oxidation. Each cycle of beta-oxidation shortens the fatty acid chain by two carbon atoms and produces one equivalent each of acetyl-CoA, NADH, and FADH2. The acetyl-CoA is metabolized by the citric acid cycle to generate ATP, while the NADH and FADH2 are used by oxidative phosphorylation to generate ATP. Dozens of ATP equivalents are generated by the beta-oxidation of a single long acyl chain. In oxidative phosphorylation, the key control point is the reaction catalyzed by cytochrome c oxidase, which is regulated by the availability of its substrate – the reduced form of cytochrome c. The amount of reduced cytochrome c available is directly related to the amounts of other substrates: 1 2 NADH + cyt c ox + ADP + P i ⇌ 1 2 NAD + + cyt c red + ATP {\displaystyle {\frac {1}{2}}{\ce {NADH}}+{\ce {cyt}}\ {\ce {c_{ox}}}+{\ce {ADP}}+{\ce {P_{i}}}\rightleftharpoons {\frac {1}{2}}{\ce {NAD^+}}+{\ce {cyt}}\ {\ce {c_{red}}}+{\ce {ATP}}}
The human form of IAPP has the amino acid sequence KCNTATCATQRLANFLVHSSNNFGAILSSTNVGSNTY, with a disulfide bridge between cysteine residues 2 and 7. Both the amidated C-terminus and the disulfide bridge are necessary for the full biological activity of amylin. IAPP is capable of forming amyloid fibrils in vitro. Within the fibrillization reaction, the early prefibrillar structures are extremely toxic to beta-cell and insuloma cell cultures. Later amyloid fiber structures also seem to have some cytotoxic effect on cell cultures. Studies have shown that fibrils are the end product and not necessarily the most toxic form of amyloid proteins/peptides in general. A non-fibril forming peptide (1–19 residues of human amylin) is toxic like the full-length peptide but the respective segment of rat amylin is not. It was also demonstrated by solid-state NMR spectroscopy that the fragment 20-29 of the human-amylin fragments membranes. Rats and mice have six substitutions (three of which are proline substitutions at positions 25, 28 and 29) that are believed to prevent the formation of amyloid fibrils, although not completely as seen by its propensity to form amyloid fibrils in vitro. Rat IAPP is nontoxic to beta-cells when overexpressed in transgenic rodents.
Immunofluorescence imaging in the human U2OS cell line (bone Osteosarcoma epithelial cells) shows localization in the cytosol. Immunohistochemistry imaging of human prostate tissue also suggests cytosolic localization. A bipartite nuclear localization signal is predicted at position 128 – 143, which is highly conserved in mammalian orthologs (see Fig.2.), indicating possible localization in the nucleus. The predicted promoter sequence for this gene spans from base pair 37196852 to 37198126 (1,275 bp) and has multiple predicted binding sites for transcription factors such as GATA binding factors, SMAD3, TP63 and NRF1. MIPOL1 is ubiquitously expressed at low levels in humans, with highest expression in the prostate. The RNA secondary structure is stabilized by multiple stem loops that have been predicted (using bioinformatics tools), and conserved across closely related species. Multiple binding targets are found for microRNAs such as MIR3163 and MIR190a, that could silence these regions on the mRNA and inhibit translation.
The American Society for Biochemistry and Molecular Biology publishes three research journals and a monthly magazine covering society news and activity updates. ASBMB journals are peer-reviewed and cover research in the fields of microbiology, molecular genetics, RNA-related research, proteomics, genomics, transcription, peptides, cell signaling, lipidomics, and systems biology. All articles are published online as "Papers in Press" upon acceptance. As of January 2021, all three ASBMB journals are fully open access.
Animals ingest amino acids in the form of protein. The protein is broken down into its constituent amino acids in the process of digestion. The amino acids are then used to synthesize new proteins and other nitrogenous biomolecules, or they are further catabolized through oxidation to provide a source of energy. The oxidation pathway starts with the removal of the amino group by a transaminase; the amino group is then fed into the urea cycle. The other product of transamidation is a keto acid that enters the citric acid cycle. Glucogenic amino acids can also be converted into glucose, through gluconeogenesis. Of the 20 standard amino acids, nine (His, Ile, Leu, Lys, Met, Phe, Thr, Trp and Val) are called essential amino acids because the human body cannot synthesize them from other compounds at the level needed for normal growth, so they must be obtained from food.
Sources: en.wikipedia.org
On-line mass spectrometry was develop to solve some of the limitations and problem that develop from off-line analysis, such as evaporation and chemical reactions of particles in the filters during long analysis time. On-line Mass spectrometry solves these problems through the collection and analysis of aerosol particles in real time. On-line instruments are very portable and allow for spatial variability to be examined. These portable instruments can be put on many different platforms such as boats, planes, and mobile platforms (e.g. car trailers). An example of this is in the picture at the beginning with the instrumentation attached to an aircraft. Like off-line, on-line mass spectrometry has many different type of instruments, which can be broken up into two types; instruments that measures the chemistry of the particle ensemble (bulk measurement) and those that measure the chemistry of individual particles (single-particle measurement). Thus based on analytical need different instrumentation is used in analysis of the aerosol particles.
The word "aptamer" is a neologism coined by Andrew D. Ellington and Jack Szostak in their first publication on the topic. They did not provide a precise definition, stating "We have termed these individual RNA sequences 'aptamers', from the Latin aptus, to fit." The word itself, however, derives from the Greek word ἅπτω, to connect or fit (as used by Homer (c. 8th century BC)) and μέρος, a component of something larger. A typical aptamer is a synthetically generated ligand exploiting the combinatorial diversity of DNA, RNA, XNA, or peptide to achieve strong, specific binding for a particular target molecule or family of target molecules. Aptamers are occasionally classified as "chemical antibodies" or "antibody mimics". However, most aptamers are small, with a molecular weight of 6-30 kDa, in contrast to the 150 kDa size of antibodies, and contain one binding site rather than the two matching antigen binding regions of a typical antibody.
An automated synthesis is very similar in procedure to performing a manual synthesis. The overseeing chemist decides on a target molecule then formulates the experimental plan, which is a sequential series of steps. Then, they collect the required equipment and execute the plan. The automated synthesis follows the same pathway, except that the computer devises and executes the experimental plan. However, human revision is usually still required to ensure the automated route is practical and there are no implicit steps or conditions missing from the proposed procedure. In organic synthesis, organic synthesis software is used to automate the process of identifying sequences of reactions or routes that can be used to synthesize organic compounds.
Three major forms of hCG are produced by humans, with each having distinct physiological roles. These include regular hCG, hyperglycosylated hCG, and the free beta-subunit of hCG. Degradation products of hCG have also been detected, including nicked hCG, hCG missing the C-terminal peptide from the beta-subunit, and free alpha-subunit, which has no known biological function. Some hCG is also made by the pituitary gland with a pattern of glycosylation that differs from placental forms of hCG. Regular hCG is the main form of hCG associated with the majority of pregnancy and in non-invasive molar pregnancies. This is produced in the trophoblast cells of the placental tissue. Hyperglycosylated hCG is the main form of hCG during the implantation phase of pregnancy, with invasive molar pregnancies, and with choriocarcinoma. Gonadotropin preparations of hCG can be produced for pharmaceutical use from animal or synthetic sources.
Mineralocorticoid hormones are synthesized in the outermost layer of the adrenal cortex known as the zona glomerulosa. Their function is to regulate the concentration of electrolytes circulating in the blood. For example, aldosterone functions to raise blood sodium levels and lower blood potassium levels by targeting the kidneys. Specifically, it binds receptors of cells that comprise the distal tubules of the kidneys which then stimulate ion channels to conserve sodium and excrete potassium. Additionally, the ion gradient initiates conservation of water. The glucocorticoid family of hormones is synthesized in the middle layer of the adrenal cortex known as the zona fasciculata. These hormones regulate the processing of proteins, fats, and carbohydrates by the human body. They also play a role in maintaining a normal stress response cycle. Androgens, or sex hormones, are synthesized in the innermost layer of the adrenal cortex known as the zona reticularis. These hormones, such as estrogen in females and testosterone in males, are commonly known for promoting sexual characteristics and the maturation of reproductive organs of the respective gender.
Sources: en.wikipedia.org
Method validation is the documented process of showing that an HPLC procedure produces reliable results for a defined purpose. It examines parameters such as accuracy, precision, specificity, linearity, and robustness. Regulators and quality systems often require validation before routine use.
System suitability is a set of checks run on the chromatographic system before sample analysis. It confirms that resolution, peak shape, retention time, and response meet predefined limits. Failure can invalidate the run and trigger corrective action.
Blank injections reveal peaks or baseline disturbances that come from solvents, reagents, or the instrument rather than the sample. They help distinguish contamination from actual analyte signals. Comparing blanks with sample runs supports accurate interpretation.
HPLC testing measures the presence and amount of one or more compounds in a liquid sample. It separates mixture components and records detector responses as peaks, which are compared with reference standards. Results are usually reported as concentrations or relative percentages.